NEW SEARCH NEW SEARCH, STATE - QLD
Next
Last
DISCLAIMER:
Whilst all care is taken to provide accurate information with respect to the item described, the Independent Living Centre (ILC) is not involved in product design or manufacture, and therefore not in a position to guarantee the accuracy of the information provided. Selection of equipment, which is both suitable and appropriate for individual needs remains the responsibility of the person(s) considering requisition, and no responsibility is taken by the ILC for any loss or injury caused through use of the equipment or alleged to have arisen through reliance upon information provided. As information is subject to change any enquiries should be directed to the manufacturer.
Item Details
Mechanical Engineering & Quality Control SF 600 Wheelchair Lifting Platform
ILC Reference NO 44:45:016
Item sourced from ILC QLD database
Short Description
The SF 600 lifting platform is capable of carrying a wheelchair and user over small height differences of up to 610mm. It does not require permanent installation and is suitable for indoor or outdoor applications.
More Details
The SF600 Lifting Platform is made from galvanised steel (inside) and aluminium (outside). Both the platform and access ramp have a slip free finish. The driving mechanism is a screw actuator, 24V DC. The main actuator is of worm gear type. In the case of a power failure it will stop at the spot the power interruption occurred. Access and drive-off are at opposite ends of the lifting platform. To ensure user safety, the access ramp functions as a gate, and there are hand rails on both sides of the SF 600.
Method of Lift Operation:
The unit is operated using a hand held control. There are only two buttons to manipulate, one for up and one for down.
To raise the lifting platform from its lowest level:
1. When the lifting platform is at its lowest level, and the access ramp has been lowered to that level, the wheelchair user can drive into/up onto the lifting platform without hindrance.
2. Pressing the UP button on the hand held controller raises the access ramp; this then functions as a guard against rolling off. The button is activated for as long as it is pressed down.
3. When the access ramp has been raised to its highest level keep pressing the UP button to raise the platform.
4. When the lifting platform is level with the landing, the platform stops automatically and the user can drive onto the landing.
To lower the lifting platform from its highest level:
1. The wheelchair user drives onto the lifting platform.
2. Activate the hand control by pressing the DOWN button to lower the lifting platform. The button is active for as long as it is pressed down.
3. When the lifting platform is at its lowest level, continue pressing the DOWN button to lower the access ramp. The user can then drive off the lifting platform.
Factors to Consider
In the case of a power failure the lift will stop at the spot the power interruption occurred.
Models
One model only - SF 600
Options
The unit can be put on its side to minimise the stowing area required.
Installation
Supplier states that it will be necessary to provide a completely flat, level load bearing concrete base with a smooth trowelled finish and of sufficient strength to support 500kg over the face of the lift.
This pad shall be large enough to accommodate the size of the lift plus the required running clearance.
It will be necessary to provide a 240 volt, 10 amp. single phase outlet at a suitable position adjacent to the lift on the lower level.
The wall adjacent to the front face of the lift in its line of travel is to be vertical and flush with no shear points.
Dimensions
Lift
Overall Width..................................... 886 mm
Load Capacity (supplier stated)................... 200 kg (max.)
Range (mm)........................................ From 95 mm to 610 mm
Platform
Width............................................. 722 mm (working width)
Length............................................ 1167 mm
Length of Platform Section........................ 1312 mm (with ramp up)
Standard
Door Access Width................................. 570 mm (minimum required)
Weight (kg)....................................... 58 kg
Stowed
Height............................................ 563 mm
Width............................................. 886 mm
Depth............................................. 1312 mm
Place Of Manufacture
Manufactured in Western Australia.
Warranty
Supplier warrants that its lifting equipment is free from defects in materials and workmanship under normal use. Supplier warrants that the lifting equipment itself will perform substantially in accordance with the specifications and the design intent of the lift.
The expressed warranties are made for a period of 365 days from the date the lifting equipment is delivered to the first user.
During that period the supplier will replace any lifting equipment, which proves defective in materials or workmanship, without additional charge, on exchange basis.
Display Item On Loan From
Townsville Display Centre:
Not on display.
Please be aware that this device may be available upon request for an individual consultation. A general consultation fee may be required for this service. Please contact LifeTec Queensland for more details.
Brisbane Display Centre:
Not on display.
Please be aware that this device may be available upon request for an individual consultation. A general consultation fee may be required for this service. Please contact LifeTec Queensland for more details.
Standards
Supplier reports that the SF 600 Lifting Platform is manufactured in Western Australia in conformance with the AS 1735.12-1994 and AS 1735.14-1998 Standards.
For some types of equipment, specific Australian or other Standards are applicable to the materials used in, and the manufacturing and installation of products. Compliance with relevant Standards is indicated by written certification that a product has been tested and assessed as compliant with specified Australian Standards. Purchasers are advised to check with the supplier or manufacturer of an item as to its compliance with the relevant Standard(s).
Price Guide
Refer to supplier details for pricing.
Supplier Information - click to supplier for contacts details
MECHANICAL ENGINEEERING AND QUALITY CONTROL (ME&QC;),
ATWELL, WA
Additional /images
Click Thumbnail to view larger image.
First
Prev
Next
Last
